Welcome, Guest
Wednesday, May 14, 2008

SIA

Is a Pressure sensitive adhesive backed tear-away stabilizer that sticks to the back of the Hoop-It-All hoops, allowing you to attach your fabric to it rather than hooping your fabric within 2 hoop frames. SIA is required to hold the fabric in place on our hoops preventing distortion and shifting of the fabric. It is available in over 60 different sizes. In some cases no other stabilizer is required such as on caps, purses, and heavy weight fabrics. SIA yields better quality embroidery than most non-adhesive stabilizers, MADE in USA.

SIA 6 inch Wide Rolls (152mm Wide)

The 6 inch series comes in 6 and 6 1/2 widths. This series of rolls is best used for piecing and our 6 inch hoops.

view stabilizers

SIA 7 inch Wide Rolls (178mm Wide)

The 7 inch series comes in 7 1/2, 7 3/4 and 7 7/8 widths.

view stabilizers

SIA 8 inch Wide Rolls (203mm Wide)

The 8 inch series comes in 8 1/4 and 8 1/2 widths.

view stabilizers

SIA 9 inch Wide Rolls (229mm Wide)

The 9 inch series comes in 9 1/8, 9 1/4, 9 5/8 and 9 7/8 widths.

view stabilizers

SIA 11 inch Wide Rolls (279mm Wide)

The 11 inch series comes in 11 inch wide rolls.

view stabilizers

SIA 12 inch Wide Rolls (305mm Wide)

The 12 inch series comes in 12 inch wide rolls.

view stabilizers

SIA 14 inch Wide Rolls (356mm Wide)

The 14 inch series comes in 14 1/4 and 14 1/2 widths.

view stabilizers

SIA 16 inch Wide Rolls (406mm Wide)

The 16 inch series comes in 16 inch wide rolls.

view stabilizers

SIA 22 inch Wide Rolls (559mm Wide)

The 22 inch series comes in 22 inch wide rolls.

view stabilizers

SIA Pressure sensitive adhesive backed tear-away stabilizer is made with polyester fibers and it adheres to the back of the Hoop-It-All, allowing you to attach your fabric to it, rather than hooping your fabric within 2 hoop frames. SIA is required to hold the fabric in place on the hoop and prevents shifting of the fabric. In some cases no other stabilizer is required such as on caps, purses, and heavy weight fabrics.  SIA yields better quality embroidery than non adhesive stabilizers.

To use SIA, peel several inches of the adhesive protective covering (release liner) and stick it on the top edge of the Hoop Frame. While pressing the SIA to the Frame, pull the remaining release liner toward the other end of the frame, until it is all removed.

Press the SIA from Corner-to-corner (diagonally) and then pull and press the opposite side. Then pull and press the SIA in the center and all around the edges, until it is smooth and taut. You are now ready to apply the fabric to embroider.

 

sia logo

SIA™ (Formerly known as Stick-It-All) is necessary for using any of the Hoop-It-All™ hoops. It adheres to the backside of the hoops-holding and stabilizing your fabric during embroidery. It holds your fabric more securely than your original factory hoops and therefore prevents the customary puckering and distortion.

If you embroider a small design and don’t want to waste an entire sheet of Stick-It-All™, you can simply cut a small piece and patch the hole, with a one inch overlap around the edges, saving you money.

New & Improved!

Many sticky back stabilizers are imported and made with paper. Stick-It-All™ however, is made in USA of polyester fibers. It tears like paper and is washable. Hoop-It-All™ has improved Stick-It-All™ 30 times in the last 13 years to improve the quality of your Embroidery.

BENEFITS

IT HOLDS:

  • Small items such as:
  •  

              Cuffs, collars, ball caps, baby socks, ribbons, ties, etc.

  • Items too large to hoop with the standard two-ring hoop process such as:

              purse flaps, dashboard covers, shoe tongue’s, jacket backs, etc.

 

IT PREVENTS:

  • Unsightly ring marks on velour and velvet.
  • Damage and shifting of fine fabrics during embroidery.
  • Interference with zippers, seams, buttons, pockets and previous emboidery.

 

IT ALLOWS YOU TO:

  • Embroider on otherwise impossible items like:
  • Collars, lapels, and cuffs.